Trainers - Indoor Exercise Bikes

Replacement straps for Sunlite FlatForm II pedals - Strap size: 340 x 55mm

Keep your handlebar organized and your devices secure with the LW-STD (22.2/25.4/28.6mm) from Minoura. - Alloy clamp for mounting your own device on handlebar or stem - Lightweight and rustproof aluminum construction - Hex wrench required for instillation and removal - Clamp body has (1) M5 Thread hold in center - 22.2 mm-28.6 mm diameter range

• Gray

The Mag Riser Block 3 from Minoura lifts up your front wheel during a training session to be at a natural level. This block fits both MTB and Road bike tire widths. - Fits under front wheel to level the bike to get natural riding on training - Double grooved design fits your narrow or wide ties - Polyethylene material minimizes weight at 1/2 lb. - 8.6D X 4.7W X 2.75H (inches)

BLE USB Adapter gives Rouvy virtual training software the ability to seamlessly connect to Bluetooth devices and sensors. The adapter contains a Bluetooth (BLE) radio that allows PCs to communicate with BLE devices, including Saris smart indoor bicycle trainers and power meters. Most importantly, the BLE USB Adapter is necessary to update the firmware Over the Air (OTA) via VirtualTraining for the Hammer and Magnus bike trainers. - Bluetooth adapter for PCs to work with Rouvy - Needed for Over the Air Firmware Updates to Smart Indoor Bike Trainers. - Works with PC desktops and laptops.

The Skyliner is a front wheel support for use with Tacx classic trainers. It raises and supports the front wheel for a natural cycling position and increased stability. It also serves as a handle to carry the trainer.

The Tacx Sweat Cover protects your bike from corrosion caused by perspiration. It is made from absorbent textile to catch and retain perspiration. Its clever design fits all bikes and enables easy mounting.

• Plastic riser block allows the position of front wheel at one of two heights

The Gel Block is an indispensable accessory for perfecting your position on the bike and provides a more natural feel to your training. - Reduces vibrations on the handlebars for more comfortable training - Non-slip Elastogel insert ensures maximum stability and alignment of the front wheel - Suitable for road and MTB

A sweat cover with a pocket for your smartphone. The sweat cover protects your bike against perspiration and enables the use of a phone while training. The Tacx sweat cover is made from absorbent textile to catch and retain perspiration. Its clever design fits all bikes and enables easy mounting. Suitable for a variety of phone sizes - max. length 138mm, max. width 68mm.

The Saris Leveling Block keeps your bike level with your trainer. - Adds stability to your training ride. - For use with any rear wheel-mounted trainer. - Raises front bicycle tire 1.1 inches (2.8 cm) off the ground

The TPH-1 Tablet Grip from Minoura is the ultimate tablet holder for indoor training. Fitting a diameter between 28mm and 35mm, this stand will fit most bicycles. - Perfect accessory to use with LiveTraining Apps, The Sufferfest videos, or other media - SM clamp easily mounts or dismounts from the handlebar or tube - Spring-loaded clamp system is simple to use and securely holds your device in place - Holds from a 7.9 to 9.7 inch screen with 360 degree rotation system - Can mount to your repair stand so you can easily reference the Internet when working on your bike

This height-adjustable front wheel support can simulate both flat terrain and slopes perfectly - Unique design with 5 levels lets you adjust the height of your front wheel to simulate hill climbs up to 6% - Anti-slip rubber feet eliminate handlebar vibrations - Internal design that guarantees maximum wheel stability - Suitable for both road and MTB - You can attach to the trainer frame when not in use for easy transport and storage

Adjust resistance on Mag trainer without leaving the saddle. - Quick Release mounting system fits most stems. - For use with the Mag bike trainer only

- Includes clutch knob and L-bolt - Basic Trainer Clutch Knob is compatible with any Wind, Mag, Mag+, Magneto or Fluid trainer that already uses L-bolt - Magnus Clutch Knob should only be used with Magnus Smart Trainer - Watch our video to learn more

The E-Thru Trainer Axle allows the use of a mountain bike in a Tacx trainer. These axles are only suitable for Tacx classic trainers.

Keeps corrosive sweat from reaching your frame. - Cell phone pouch included.

The Tacx trainer tires have been developed specifically for riding indoors on bike trainers. The special rubber minimizes the risk of overheating, slipping, and wear and tear. They are also quieter than regular rear tires on both road and mountain bikes. Tacx trainer tires are not suitable for outside riding.

Our Trainer Axle is designed to adapt your thru-axle equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season. - When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out. - The axle shaft and axle ends are precision CNC-machined from 7075 aluminum and hard-anodized for rugged durability. - No special tools required. Design allows for installation or wheel removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world. Important: Before you order, make sure your specific trainer will accommodate the width of your modern thru-axle-equipped bike. Measure your trainer at the widest setting and measure the outside width of your bike frame. Our the trainer axle ends will extend past your frame on each side.

Our Trainer Axle is designed to adapt your Surly MDS/Gnot Boost thru-axle-equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season. - This axle is for Surly bikes with the MDS/Gnot Boost system. - When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out. - The axle shaft and axle ends are precision CNC-machined from 7075 aluminum, and hard-anodized for rugged durability. - No special tools required. Design allows for wheel installation or removal using your standard 5 mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world.

• 35.5-inches x 79-inches • Black

The Elite Folding Mat increases the comfort of your home cycling setup while protecting the surfaces you train on every day. It's easy to use, store, and transport and can be stored everywhere in your house. Dimensions: 1.8m x .9m

Protects the bicycle from sweat and avoids corrosions or rust. - Prevents an accumulation of sweat on the frame and components that would lead to corrosion or affect the finish - Sits above the top-tube and can be adjusted for different bicycles - Washing-machine friendly

Of course you love your Omnium Trainer, but you’re left wondering how you could possibly love indoor cycling training even more. Easy, our non-slip and water-repellent (aka sweat) Floor Mat is designed to keep you safe and protect your floors while in your cycling cleats indoors. And because your cycling training plan asks for incredibly intense efforts, the Floor Mat can ensure firm contact with the ground and prevent movement during leg-busting intervals. Add a Sweat Guard to your indoor cycling collection and you’ve got a training party! - Non-slip surface keep you safe while in cycling cleats - Protects floors from sweat and bike grime - Water-repellent surface does what it was designed to do – keep sweat off your floor - Compress-ability ensures trainer stays put during intense efforts - Easily rolls up for storage - Cleans easily with soap and water - Absorbs noise and vibration - Enhances overall stability of any indoor trainer setup - 4mm (5/32?) thickness is optimal balance of support and storage

For a stable, worry-free ride with any rear wheel-mounted trainer. Product Features - For a stable, worry-free ride with any rear wheel-mounted trainer. - Unique 3-level design lets you select the level of difficulty. - Stack two blocks to simulate climbing workouts. Three different positions to raise your front wheel and simulate hill climbs - 2.1 inches (5.3 cm) - 2.7 inches (6.8 cm) - 3.1 inches (7.9 cm)

The Saris thru axle adapter is designed for indoor use on Saris- or CycleOps-branded trainers only and should not be ridden outdoors. - Compatible with Classic series trainers and most Pro series trainers. Not compatible with PowerSync trainers. Contact us with trainer compatibility questions. - This adapter is designed to work with bikes that have a 142x12mm thru axle with 1.0 or 1.75 thread pitch. - The axle is threaded on both sides to fit both Syntace and Maxle/ABP style thru axle systems. - Many bike manufacturers do not publish thread pitch or hub spacing online. If you are unclear as to what type of thru axle your bike uses, please reach out to your local bike shop or the bicycle manufacturer directly. What's Included - Thru axle - Washers - End caps with bolts

Connect your PC to CycleOps VirtualTraining.

- Adapter for Tacx Direct Drive trainer - 01 is compatible with 142 x 12mm and 148 x 12mm - 02 is compatible with 135 x 10mm - 03 is compatible with 135 x 12mm (w/5 mm spacer included with every Tacx Direct Drive trainer), 142 x 12mm and 148 x 12mm - 04 The thru axle adapter kit is for bikes with a 12 mm thru axle. The axle adapter is required to couple the rear stay with the thru axle mount on a Tacx NEO or FLUX Smart trainer.

- Sram XD and XDR freehub for Direct Drive trainers (Drivo and Direto's family, Suito, Turno, Kura, Turbo Roteo and Volano). - Compatible with 12 speed cassette.

Adapts a thru axle hub bike for a Saris bike trainer. - Trainer Thru Axle Adapter For Saris Trainers - Thread pitch: 1.00 & 1.75 What's Included: - Thru axle - Washers - Endcaps with bolts Trainer Compatibility The Saris Trainer Thru Axle Adapter is designed for indoor use on Saris trainers only and should not be ridden outdoors. Compatible with current basic trainers. Not compatible with CycleOps PowerSync trainers. Contact us with trainer compatibility questions. Bike Compatibility Many bike manufacturers do not publish thread pitch or hub spacing online. If you are unclear as to what type of thru axle your bike uses, please contact us.